43+ Esun Pla Plus Stringing Vers

43+ Esun Pla Plus Stringing Vers. I get perfect results with all the colors, besides the white that i have some stringing and some blobs and zits, maybe a bad spool. It is direct drive so retraction amount is different. Managed to get it to extrude okay, but temp was way up to 230°c and even at that temp there's still some underextrusion. The esun pla+ printed better aside from the stringing.

Coolste Esun Filament Stringing Black Pla R Fixmyprint

I use esun pla plus and my nozzle temp is 216c and retraction speed is 40mm/s. But every machine is different. Others have experienced nozzle clogging, likely as a result of inconsistent filament diameters. If you need any support please leave your feedback. I do suggest that you do a pid tune if you haven't run one.

23.10.2019 · stringing is gone, but underextrudes badly with default pla profile at 210°c.

My basic settings in cura are: Managed to get it to extrude okay, but temp was way up to 230°c and even at that temp there's still some underextrusion. 23.10.2019 · stringing is gone, but underextrudes badly with default pla profile at 210°c. It is direct drive so retraction amount is different. Modified rostock max v2, prusa mk2, prusa mk3. See pics, the failed print was at 210 and the other at 230 and slowed down the speed.

Managed to get it to extrude okay, but temp was way up to 230°c and even at that temp there's still some underextrusion... I use esun pla+ and is working really good for me. 16.03.2021 · compared to other pla plus filament, the esun pla pro might be one of the more difficult ones to work with. 17.08.2019 · posted november 25, 2020 · esun pla+ stringing/underextrusion just joined this forum.

60, retraction 4,5 mm, retraction speed:. Until i tried to print the bullseye fan duct, that's when i first encountered I get perfect results with all the colors, besides the white that i have some stringing and some blobs and zits, maybe a bad spool. Hotend temp 210, bed temp:. Reducing the drag on the filament as much as possible.

23.10.2019 · stringing is gone, but underextrudes badly with default pla profile at 210°c.. I do suggest that you do a pid tune if you haven't run one.

See pics, the failed print was at 210 and the other at 230 and slowed down the speed... Users have reported excessive stringing when printing with this filament. 16.03.2021 · compared to other pla plus filament, the esun pla pro might be one of the more difficult ones to work with. It is direct drive so retraction amount is different. Modified rostock max v2, prusa mk2, prusa mk3.

A bit high for the bed, but it sticks amazingly well at this temp on the standard buildtak buildplate. Managed to get it to extrude okay, but temp was way up to 230°c and even at that temp there's still some underextrusion. Hotend temp 210, bed temp:.. It is direct drive so retraction amount is different.

Two things played a roll in all but eliminating stringing with amazon and inland plas for me. It is direct drive so retraction amount is different. Managed to get it to extrude okay, but temp was way up to 230°c and even at that temp there's still some underextrusion... At this point the only time i have failures now is when a spool binds up for some reason (wrong tension on the auto.

Getting it to print perfectly might take some work, but it works. See pics, the failed print was at 210 and the other at 230 and slowed down the speed. How familiar are you with all of the printing settings in your slicer? I use a test model (attached) with 10mm tall cone type towers of.. The esun pla+ printed better aside from the stringing.

New comments cannot be posted and votes cannot be cast... I get perfect results with all the colors, besides the white that i have some stringing and some blobs and zits, maybe a bad spool. Pla+285h1 (multiple colors) feedback reach | rohs msds. The esun pla+ printed better aside from the stringing. When i first started 3d printing, i didn't know that my esun pla+ had a temperature range that was higher than normal pla, so all i did was follow this profile i found on youtube and printed at 195. My basic settings in cura are: 17.08.2019 · posted november 25, 2020 · esun pla+ stringing/underextrusion just joined this forum. I have to say that i was fairly satisfied with the print quality i was getting then.

60, retraction 4,5 mm, retraction speed:.. Two things played a roll in all but eliminating stringing with amazon and inland plas for me. 60, retraction 4,5 mm, retraction speed: Hotend temp 210, bed temp: Others have experienced nozzle clogging, likely as a result of inconsistent filament diameters. 16.03.2021 · compared to other pla plus filament, the esun pla pro might be one of the more difficult ones to work with... 60, retraction 4,5 mm, retraction speed:

I use esun pla+ and is working really good for me. Getting it to print perfectly might take some work, but it works.. New comments cannot be posted and votes cannot be cast.

I get perfect results with all the colors, besides the white that i have some stringing and some blobs and zits, maybe a bad spool.. See pics, the failed print was at 210 and the other at 230 and slowed down the speed. My basic settings in cura are: But every machine is different. The esun pla+ printed better aside from the stringing. Printer i am using is a sovol sv01 (direct drive) at (after a lot of fiddling) 205c/60c, 1.2mm/50mm/s retraction. Been up and down all the relevant cura settings with virtually no effect. Hotend temp 210, bed temp: How familiar are you with all of the printing settings in your slicer?

I do suggest that you do a pid tune if you haven't run one. I print their pla+ at 205c, 60c bed. When i first started 3d printing, i didn't know that my esun pla+ had a temperature range that was higher than normal pla, so all i did was follow this profile i found on youtube and printed at 195. A bit high for the bed, but it sticks amazingly well at this temp on the standard buildtak buildplate.. Setting unload speed at start to 120mm/s.

Reducing the drag on the filament as much as possible. I do suggest that you do a pid tune if you haven't run one. But every machine is different. I get perfect results with all the colors, besides the white that i have some stringing and some blobs and zits, maybe a bad spool. I use a test model (attached) with 10mm tall cone type towers of. Users have reported excessive stringing when printing with this filament. Esun pla+ is a bit prone to stringing, so you want to make sure your retraction is set right (and stringing def increases at higher temps). Reducing the drag on the filament as much as possible. Setting unload speed at start to 120mm/s. When i first started 3d printing, i didn't know that my esun pla+ had a temperature range that was higher than normal pla, so all i did was follow this profile i found on youtube and printed at 195. Pla+285h1 (multiple colors) feedback reach | rohs msds... Users have reported excessive stringing when printing with this filament.

Make sure you do it with the fan … Modified rostock max v2, prusa mk2, prusa mk3. See pics, the failed print was at 210 and the other at 230 and slowed down the speed. I use a test model (attached) with 10mm tall cone type towers of. Users have reported excessive stringing when printing with this filament.. I get perfect results with all the colors, besides the white that i have some stringing and some blobs and zits, maybe a bad spool.

Others have experienced nozzle clogging, likely as a result of inconsistent filament diameters. It is direct drive so retraction amount is different. New comments cannot be posted and votes cannot be cast. See pics, the failed print was at 210 and the other at 230 and slowed down the speed.. 23.10.2019 · stringing is gone, but underextrudes badly with default pla profile at 210°c.

It is direct drive so retraction amount is different... Been up and down all the relevant cura settings with virtually no effect. I have to say that i was fairly satisfied with the print quality i was getting then. Managed to get it to extrude okay, but temp was way up to 230°c and even at that temp there's still some underextrusion. But every machine is different. Brand:esun pla + printing parameters: At this point the only time i have failures now is when a spool binds up for some reason (wrong tension on the auto. 17.08.2019 · posted november 25, 2020 · esun pla+ stringing/underextrusion just joined this forum.. My basic settings in cura are:

If you need any support please leave your feedback... . Esun pla+ is a bit prone to stringing, so you want to make sure your retraction is set right (and stringing def increases at higher temps).

Managed to get it to extrude okay, but temp was way up to 230°c and even at that temp there's still some underextrusion... I have to say that i was fairly satisfied with the print quality i was getting then. Two things played a roll in all but eliminating stringing with amazon and inland plas for me. At this point the only time i have failures now is when a spool binds up for some reason (wrong tension on the auto. 23.10.2019 · stringing is gone, but underextrudes badly with default pla profile at 210°c. Printer i am using is a sovol sv01 (direct drive) at (after a lot of fiddling) 205c/60c, 1.2mm/50mm/s retraction. See pics, the failed print was at 210 and the other at 230 and slowed down the speed. Pla+285h1 (multiple colors) feedback reach | rohs msds. Modified rostock max v2, prusa mk2, prusa mk3.. Been up and down all the relevant cura settings with virtually no effect.

Stringing is usually caused by a classic case of not enough retraction. When i first started 3d printing, i didn't know that my esun pla+ had a temperature range that was higher than normal pla, so all i did was follow this profile i found on youtube and printed at 195. The esun pla+ printed better aside from the stringing... Been up and down all the relevant cura settings with virtually no effect.

When i first started 3d printing, i didn't know that my esun pla+ had a temperature range that was higher than normal pla, so all i did was follow this profile i found on youtube and printed at 195.. I use esun pla+ and is working really good for me. See pics, the failed print was at 210 and the other at 230 and slowed down the speed... My basic settings in cura are:

Been up and down all the relevant cura settings with virtually no effect. When i first started 3d printing, i didn't know that my esun pla+ had a temperature range that was higher than normal pla, so all i did was follow this profile i found on youtube and printed at 195. I have to say that i was fairly satisfied with the print quality i was getting then. Esun pla+ is a bit prone to stringing, so you want to make sure your retraction is set right (and stringing def increases at higher temps). A bit high for the bed, but it sticks amazingly well at this temp on the standard buildtak buildplate. If you need any support please leave your feedback. Make sure you do it with the fan … Still, the reviews for the pla pro aren't all bad. It is direct drive so retraction amount is different.

Brand:esun pla + printing parameters: I have to say that i was fairly satisfied with the print quality i was getting then. I use esun pla+ and is working really good for me. Esun pla+ is a bit prone to stringing, so you want to make sure your retraction is set right (and stringing def increases at higher temps). 60, retraction 4,5 mm, retraction speed: I print their pla+ at 205c, 60c bed. Until i tried to print the bullseye fan duct, that's when i first encountered 17.08.2019 · posted november 25, 2020 · esun pla+ stringing/underextrusion just joined this forum. The esun pla+ printed better aside from the stringing. See pics, the failed print was at 210 and the other at 230 and slowed down the speed.

When i first started 3d printing, i didn't know that my esun pla+ had a temperature range that was higher than normal pla, so all i did was follow this profile i found on youtube and printed at 195. Two things played a roll in all but eliminating stringing with amazon and inland plas for me. It is direct drive so retraction amount is different. Been up and down all the relevant cura settings with virtually no effect. Reducing the drag on the filament as much as possible. Printer i am using is a sovol sv01 (direct drive) at (after a lot of fiddling) 205c/60c, 1.2mm/50mm/s retraction... See pics, the failed print was at 210 and the other at 230 and slowed down the speed.

I use a test model (attached) with 10mm tall cone type towers of. Printer i am using is a sovol sv01 (direct drive) at (after a lot of fiddling) 205c/60c, 1.2mm/50mm/s retraction.

See pics, the failed print was at 210 and the other at 230 and slowed down the speed... It is direct drive so retraction amount is different. A bit high for the bed, but it sticks amazingly well at this temp on the standard buildtak buildplate... Printer i am using is a sovol sv01 (direct drive) at (after a lot of fiddling) 205c/60c, 1.2mm/50mm/s retraction.

Hotend temp 210, bed temp: 60, retraction 4,5 mm, retraction speed: Getting it to print perfectly might take some work, but it works. Esun pla+ is a bit prone to stringing, so you want to make sure your retraction is set right (and stringing def increases at higher temps). Others have experienced nozzle clogging, likely as a result of inconsistent filament diameters. My basic settings in cura are: I use esun pla+ and is working really good for me. Modified rostock max v2, prusa mk2, prusa mk3. Make sure you do it with the fan …. Stringing is usually caused by a classic case of not enough retraction.

When i first started 3d printing, i didn't know that my esun pla+ had a temperature range that was higher than normal pla, so all i did was follow this profile i found on youtube and printed at 195. 16.03.2021 · compared to other pla plus filament, the esun pla pro might be one of the more difficult ones to work with. Hotend temp 210, bed temp: Two things played a roll in all but eliminating stringing with amazon and inland plas for me. Managed to get it to extrude okay, but temp was way up to 230°c and even at that temp there's still some underextrusion.. If you need any support please leave your feedback.

17.08.2019 · posted november 25, 2020 · esun pla+ stringing/underextrusion just joined this forum. Until i tried to print the bullseye fan duct, that's when i first encountered

17.08.2019 · posted november 25, 2020 · esun pla+ stringing/underextrusion just joined this forum... Two things played a roll in all but eliminating stringing with amazon and inland plas for me. At this point the only time i have failures now is when a spool binds up for some reason (wrong tension on the auto. The esun pla+ printed better aside from the stringing. Getting it to print perfectly might take some work, but it works... I have to say that i was fairly satisfied with the print quality i was getting then.

A bit high for the bed, but it sticks amazingly well at this temp on the standard buildtak buildplate... I print their pla+ at 205c, 60c bed. Users have reported excessive stringing when printing with this filament. New comments cannot be posted and votes cannot be cast. Hotend temp 210, bed temp:.. My basic settings in cura are:

I use esun pla plus and my nozzle temp is 216c and retraction speed is 40mm/s. Setting unload speed at start to 120mm/s. A bit high for the bed, but it sticks amazingly well at this temp on the standard buildtak buildplate. Two things played a roll in all but eliminating stringing with amazon and inland plas for me. Pla+285h1 (multiple colors) feedback reach | rohs msds. Printer i am using is a sovol sv01 (direct drive) at (after a lot of fiddling) 205c/60c, 1.2mm/50mm/s retraction.

Been up and down all the relevant cura settings with virtually no effect... Printer i am using is a sovol sv01 (direct drive) at (after a lot of fiddling) 205c/60c, 1.2mm/50mm/s retraction... How familiar are you with all of the printing settings in your slicer?

17.08.2019 · posted november 25, 2020 · esun pla+ stringing/underextrusion just joined this forum.. I print their pla+ at 205c, 60c bed. Users have reported excessive stringing when printing with this filament. I do suggest that you do a pid tune if you haven't run one. The esun pla+ printed better aside from the stringing.

Setting unload speed at start to 120mm/s. 17.08.2019 · posted november 25, 2020 · esun pla+ stringing/underextrusion just joined this forum. 23.10.2019 · stringing is gone, but underextrudes badly with default pla profile at 210°c. The esun pla+ printed better aside from the stringing. When i first started 3d printing, i didn't know that my esun pla+ had a temperature range that was higher than normal pla, so all i did was follow this profile i found on youtube and printed at 195.. I get perfect results with all the colors, besides the white that i have some stringing and some blobs and zits, maybe a bad spool.

But every machine is different. .. A bit high for the bed, but it sticks amazingly well at this temp on the standard buildtak buildplate.

Modified rostock max v2, prusa mk2, prusa mk3. Managed to get it to extrude okay, but temp was way up to 230°c and even at that temp there's still some underextrusion... I use esun pla+ and is working really good for me.

Managed to get it to extrude okay, but temp was way up to 230°c and even at that temp there's still some underextrusion... 60, retraction 4,5 mm, retraction speed:

Stringing is usually caused by a classic case of not enough retraction.. I use esun pla+ and is working really good for me. I get perfect results with all the colors, besides the white that i have some stringing and some blobs and zits, maybe a bad spool. Others have experienced nozzle clogging, likely as a result of inconsistent filament diameters. Reducing the drag on the filament as much as possible. 23.10.2019 · stringing is gone, but underextrudes badly with default pla profile at 210°c.. I use a test model (attached) with 10mm tall cone type towers of.

17.08.2019 · posted november 25, 2020 · esun pla+ stringing/underextrusion just joined this forum. 60, retraction 4,5 mm, retraction speed: Users have reported excessive stringing when printing with this filament. I do suggest that you do a pid tune if you haven't run one. Printer i am using is a sovol sv01 (direct drive) at (after a lot of fiddling) 205c/60c, 1.2mm/50mm/s retraction. Been up and down all the relevant cura settings with virtually no effect. Still, the reviews for the pla pro aren't all bad. 17.08.2019 · posted november 25, 2020 · esun pla+ stringing/underextrusion just joined this forum. I get perfect results with all the colors, besides the white that i have some stringing and some blobs and zits, maybe a bad spool. I print their pla+ at 205c, 60c bed. Make sure you do it with the fan …. But every machine is different.

16.03.2021 · compared to other pla plus filament, the esun pla pro might be one of the more difficult ones to work with. Two things played a roll in all but eliminating stringing with amazon and inland plas for me. Been up and down all the relevant cura settings with virtually no effect. Stringing is usually caused by a classic case of not enough retraction. Until i tried to print the bullseye fan duct, that's when i first encountered I print their pla+ at 205c, 60c bed. Modified rostock max v2, prusa mk2, prusa mk3. Setting unload speed at start to 120mm/s... Printer i am using is a sovol sv01 (direct drive) at (after a lot of fiddling) 205c/60c, 1.2mm/50mm/s retraction.

How familiar are you with all of the printing settings in your slicer? I do suggest that you do a pid tune if you haven't run one. It is direct drive so retraction amount is different. Reducing the drag on the filament as much as possible. 17.08.2019 · posted november 25, 2020 · esun pla+ stringing/underextrusion just joined this forum. Modified rostock max v2, prusa mk2, prusa mk3. Still, the reviews for the pla pro aren't all bad. Brand:esun pla + printing parameters:. At this point the only time i have failures now is when a spool binds up for some reason (wrong tension on the auto.

I print their pla+ at 205c, 60c bed.. Reducing the drag on the filament as much as possible. 23.10.2019 · stringing is gone, but underextrudes badly with default pla profile at 210°c. I use esun pla+ and is working really good for me. Users have reported excessive stringing when printing with this filament. 60, retraction 4,5 mm, retraction speed: 16.03.2021 · compared to other pla plus filament, the esun pla pro might be one of the more difficult ones to work with. Others have experienced nozzle clogging, likely as a result of inconsistent filament diameters. Modified rostock max v2, prusa mk2, prusa mk3. My basic settings in cura are:. Two things played a roll in all but eliminating stringing with amazon and inland plas for me.

17.08.2019 · posted november 25, 2020 · esun pla+ stringing/underextrusion just joined this forum... I get perfect results with all the colors, besides the white that i have some stringing and some blobs and zits, maybe a bad spool. Printer i am using is a sovol sv01 (direct drive) at (after a lot of fiddling) 205c/60c, 1.2mm/50mm/s retraction.. Make sure you do it with the fan …

23.10.2019 · stringing is gone, but underextrudes badly with default pla profile at 210°c. It is direct drive so retraction amount is different. Until i tried to print the bullseye fan duct, that's when i first encountered Users have reported excessive stringing when printing with this filament.

But every machine is different. I have to say that i was fairly satisfied with the print quality i was getting then. 60, retraction 4,5 mm, retraction speed: Reducing the drag on the filament as much as possible. It is direct drive so retraction amount is different. The esun pla+ printed better aside from the stringing. See pics, the failed print was at 210 and the other at 230 and slowed down the speed. When i first started 3d printing, i didn't know that my esun pla+ had a temperature range that was higher than normal pla, so all i did was follow this profile i found on youtube and printed at 195. Modified rostock max v2, prusa mk2, prusa mk3. Setting unload speed at start to 120mm/s.. Setting unload speed at start to 120mm/s.

16.03.2021 · compared to other pla plus filament, the esun pla pro might be one of the more difficult ones to work with. I use a test model (attached) with 10mm tall cone type towers of. Users have reported excessive stringing when printing with this filament. 16.03.2021 · compared to other pla plus filament, the esun pla pro might be one of the more difficult ones to work with. Hotend temp 210, bed temp: Pla+285h1 (multiple colors) feedback reach | rohs msds. My basic settings in cura are: Make sure you do it with the fan … Managed to get it to extrude okay, but temp was way up to 230°c and even at that temp there's still some underextrusion. Getting it to print perfectly might take some work, but it works. Setting unload speed at start to 120mm/s.. How familiar are you with all of the printing settings in your slicer?

I use a test model (attached) with 10mm tall cone type towers of... I use a test model (attached) with 10mm tall cone type towers of. Stringing is usually caused by a classic case of not enough retraction. 17.08.2019 · posted november 25, 2020 · esun pla+ stringing/underextrusion just joined this forum. Others have experienced nozzle clogging, likely as a result of inconsistent filament diameters. Make sure you do it with the fan … Reducing the drag on the filament as much as possible. Managed to get it to extrude okay, but temp was way up to 230°c and even at that temp there's still some underextrusion. I print their pla+ at 205c, 60c bed.. Still, the reviews for the pla pro aren't all bad.

At this point the only time i have failures now is when a spool binds up for some reason (wrong tension on the auto... Brand:esun pla + printing parameters: 16.03.2021 · compared to other pla plus filament, the esun pla pro might be one of the more difficult ones to work with. My basic settings in cura are: How familiar are you with all of the printing settings in your slicer?.. Make sure you do it with the fan …

When i first started 3d printing, i didn't know that my esun pla+ had a temperature range that was higher than normal pla, so all i did was follow this profile i found on youtube and printed at 195. But every machine is different. When i first started 3d printing, i didn't know that my esun pla+ had a temperature range that was higher than normal pla, so all i did was follow this profile i found on youtube and printed at 195. Reducing the drag on the filament as much as possible. Make sure you do it with the fan … Modified rostock max v2, prusa mk2, prusa mk3. Two things played a roll in all but eliminating stringing with amazon and inland plas for me. I have to say that i was fairly satisfied with the print quality i was getting then... Stringing is usually caused by a classic case of not enough retraction.

I do suggest that you do a pid tune if you haven't run one.. Setting unload speed at start to 120mm/s. See pics, the failed print was at 210 and the other at 230 and slowed down the speed. New comments cannot be posted and votes cannot be cast. 60, retraction 4,5 mm, retraction speed: Managed to get it to extrude okay, but temp was way up to 230°c and even at that temp there's still some underextrusion. A bit high for the bed, but it sticks amazingly well at this temp on the standard buildtak buildplate. Make sure you do it with the fan … Brand:esun pla + printing parameters:.. My basic settings in cura are:

I use esun pla plus and my nozzle temp is 216c and retraction speed is 40mm/s. 23.10.2019 · stringing is gone, but underextrudes badly with default pla profile at 210°c. Modified rostock max v2, prusa mk2, prusa mk3. Modified rostock max v2, prusa mk2, prusa mk3.

Others have experienced nozzle clogging, likely as a result of inconsistent filament diameters. The esun pla+ printed better aside from the stringing.

16.03.2021 · compared to other pla plus filament, the esun pla pro might be one of the more difficult ones to work with.. When i first started 3d printing, i didn't know that my esun pla+ had a temperature range that was higher than normal pla, so all i did was follow this profile i found on youtube and printed at 195. I use esun pla plus and my nozzle temp is 216c and retraction speed is 40mm/s. How familiar are you with all of the printing settings in your slicer? Users have reported excessive stringing when printing with this filament. 23.10.2019 · stringing is gone, but underextrudes badly with default pla profile at 210°c. I print their pla+ at 205c, 60c bed. Brand:esun pla + printing parameters:.. The esun pla+ printed better aside from the stringing.

Hotend temp 210, bed temp: Getting it to print perfectly might take some work, but it works. The esun pla+ printed better aside from the stringing. I use a test model (attached) with 10mm tall cone type towers of. A bit high for the bed, but it sticks amazingly well at this temp on the standard buildtak buildplate.

How familiar are you with all of the printing settings in your slicer?. Users have reported excessive stringing when printing with this filament. I use esun pla+ and is working really good for me. 17.08.2019 · posted november 25, 2020 · esun pla+ stringing/underextrusion just joined this forum. I print their pla+ at 205c, 60c bed. I use esun pla plus and my nozzle temp is 216c and retraction speed is 40mm/s. 60, retraction 4,5 mm, retraction speed: Managed to get it to extrude okay, but temp was way up to 230°c and even at that temp there's still some underextrusion. New comments cannot be posted and votes cannot be cast.

I use a test model (attached) with 10mm tall cone type towers of. Getting it to print perfectly might take some work, but it works. Setting unload speed at start to 120mm/s. New comments cannot be posted and votes cannot be cast. 16.03.2021 · compared to other pla plus filament, the esun pla pro might be one of the more difficult ones to work with. But every machine is different... My basic settings in cura are:

Getting it to print perfectly might take some work, but it works... I have to say that i was fairly satisfied with the print quality i was getting then. But every machine is different. Until i tried to print the bullseye fan duct, that's when i first encountered

Reducing the drag on the filament as much as possible.. See pics, the failed print was at 210 and the other at 230 and slowed down the speed. Still, the reviews for the pla pro aren't all bad. I print their pla+ at 205c, 60c bed. But every machine is different. Managed to get it to extrude okay, but temp was way up to 230°c and even at that temp there's still some underextrusion.. Reducing the drag on the filament as much as possible.

The esun pla+ printed better aside from the stringing... Been up and down all the relevant cura settings with virtually no effect. 16.03.2021 · compared to other pla plus filament, the esun pla pro might be one of the more difficult ones to work with. I print their pla+ at 205c, 60c bed. I use a test model (attached) with 10mm tall cone type towers of. New comments cannot be posted and votes cannot be cast. 17.08.2019 · posted november 25, 2020 · esun pla+ stringing/underextrusion just joined this forum. A bit high for the bed, but it sticks amazingly well at this temp on the standard buildtak buildplate. 60, retraction 4,5 mm, retraction speed: Reducing the drag on the filament as much as possible. I have to say that i was fairly satisfied with the print quality i was getting then.. I print their pla+ at 205c, 60c bed.

If you need any support please leave your feedback... I use a test model (attached) with 10mm tall cone type towers of. I print their pla+ at 205c, 60c bed. Brand:esun pla + printing parameters: Printer i am using is a sovol sv01 (direct drive) at (after a lot of fiddling) 205c/60c, 1.2mm/50mm/s retraction. See pics, the failed print was at 210 and the other at 230 and slowed down the speed. Pla+285h1 (multiple colors) feedback reach | rohs msds. Been up and down all the relevant cura settings with virtually no effect. Make sure you do it with the fan …. Two things played a roll in all but eliminating stringing with amazon and inland plas for me.

I have to say that i was fairly satisfied with the print quality i was getting then... A bit high for the bed, but it sticks amazingly well at this temp on the standard buildtak buildplate. Until i tried to print the bullseye fan duct, that's when i first encountered Stringing is usually caused by a classic case of not enough retraction. Reducing the drag on the filament as much as possible. I use esun pla+ and is working really good for me... Two things played a roll in all but eliminating stringing with amazon and inland plas for me.

60, retraction 4,5 mm, retraction speed: My basic settings in cura are: Two things played a roll in all but eliminating stringing with amazon and inland plas for me. 17.08.2019 · posted november 25, 2020 · esun pla+ stringing/underextrusion just joined this forum.

At this point the only time i have failures now is when a spool binds up for some reason (wrong tension on the auto. See pics, the failed print was at 210 and the other at 230 and slowed down the speed. I have to say that i was fairly satisfied with the print quality i was getting then. If you need any support please leave your feedback. The esun pla+ printed better aside from the stringing. 23.10.2019 · stringing is gone, but underextrudes badly with default pla profile at 210°c.. Pla+285h1 (multiple colors) feedback reach | rohs msds.

New comments cannot be posted and votes cannot be cast... My basic settings in cura are: At this point the only time i have failures now is when a spool binds up for some reason (wrong tension on the auto. Esun pla+ is a bit prone to stringing, so you want to make sure your retraction is set right (and stringing def increases at higher temps). When i first started 3d printing, i didn't know that my esun pla+ had a temperature range that was higher than normal pla, so all i did was follow this profile i found on youtube and printed at 195. A bit high for the bed, but it sticks amazingly well at this temp on the standard buildtak buildplate... How familiar are you with all of the printing settings in your slicer?

23.10.2019 · stringing is gone, but underextrudes badly with default pla profile at 210°c. Reducing the drag on the filament as much as possible. I use a test model (attached) with 10mm tall cone type towers of. Setting unload speed at start to 120mm/s. How familiar are you with all of the printing settings in your slicer? Been up and down all the relevant cura settings with virtually no effect. Getting it to print perfectly might take some work, but it works. Brand:esun pla + printing parameters: Modified rostock max v2, prusa mk2, prusa mk3. I have to say that i was fairly satisfied with the print quality i was getting then.. Others have experienced nozzle clogging, likely as a result of inconsistent filament diameters.

But every machine is different. Users have reported excessive stringing when printing with this filament. Pla+285h1 (multiple colors) feedback reach | rohs msds. Still, the reviews for the pla pro aren't all bad. I have to say that i was fairly satisfied with the print quality i was getting then. Esun pla+ is a bit prone to stringing, so you want to make sure your retraction is set right (and stringing def increases at higher temps). Been up and down all the relevant cura settings with virtually no effect. It is direct drive so retraction amount is different. If you need any support please leave your feedback. Reducing the drag on the filament as much as possible. I do suggest that you do a pid tune if you haven't run one... I use esun pla+ and is working really good for me.

23.10.2019 · stringing is gone, but underextrudes badly with default pla profile at 210°c. Esun pla+ is a bit prone to stringing, so you want to make sure your retraction is set right (and stringing def increases at higher temps). 60, retraction 4,5 mm, retraction speed: A bit high for the bed, but it sticks amazingly well at this temp on the standard buildtak buildplate. Others have experienced nozzle clogging, likely as a result of inconsistent filament diameters. 16.03.2021 · compared to other pla plus filament, the esun pla pro might be one of the more difficult ones to work with. Printer i am using is a sovol sv01 (direct drive) at (after a lot of fiddling) 205c/60c, 1.2mm/50mm/s retraction. Pla+285h1 (multiple colors) feedback reach | rohs msds. It is direct drive so retraction amount is different.

But every machine is different. Others have experienced nozzle clogging, likely as a result of inconsistent filament diameters. 17.08.2019 · posted november 25, 2020 · esun pla+ stringing/underextrusion just joined this forum. Modified rostock max v2, prusa mk2, prusa mk3. A bit high for the bed, but it sticks amazingly well at this temp on the standard buildtak buildplate. I use a test model (attached) with 10mm tall cone type towers of... Esun pla+ is a bit prone to stringing, so you want to make sure your retraction is set right (and stringing def increases at higher temps).

Getting it to print perfectly might take some work, but it works. Others have experienced nozzle clogging, likely as a result of inconsistent filament diameters. I use esun pla plus and my nozzle temp is 216c and retraction speed is 40mm/s. 23.10.2019 · stringing is gone, but underextrudes badly with default pla profile at 210°c. Getting it to print perfectly might take some work, but it works. My basic settings in cura are:. I use esun pla+ and is working really good for me.

Getting it to print perfectly might take some work, but it works... The esun pla+ printed better aside from the stringing. 16.03.2021 · compared to other pla plus filament, the esun pla pro might be one of the more difficult ones to work with. Until i tried to print the bullseye fan duct, that's when i first encountered I get perfect results with all the colors, besides the white that i have some stringing and some blobs and zits, maybe a bad spool. It is direct drive so retraction amount is different. Others have experienced nozzle clogging, likely as a result of inconsistent filament diameters. I use esun pla+ and is working really good for me. It is direct drive so retraction amount is different.

60, retraction 4,5 mm, retraction speed: Managed to get it to extrude okay, but temp was way up to 230°c and even at that temp there's still some underextrusion. 16.03.2021 · compared to other pla plus filament, the esun pla pro might be one of the more difficult ones to work with. Pla+285h1 (multiple colors) feedback reach | rohs msds. Printer i am using is a sovol sv01 (direct drive) at (after a lot of fiddling) 205c/60c, 1.2mm/50mm/s retraction. Make sure you do it with the fan … I use esun pla+ and is working really good for me. My basic settings in cura are: Users have reported excessive stringing when printing with this filament.. Hotend temp 210, bed temp:

I use esun pla plus and my nozzle temp is 216c and retraction speed is 40mm/s. See pics, the failed print was at 210 and the other at 230 and slowed down the speed. Stringing is usually caused by a classic case of not enough retraction. My basic settings in cura are: Brand:esun pla + printing parameters: Pla+285h1 (multiple colors) feedback reach | rohs msds. Reducing the drag on the filament as much as possible. It is direct drive so retraction amount is different. 23.10.2019 · stringing is gone, but underextrudes badly with default pla profile at 210°c. Others have experienced nozzle clogging, likely as a result of inconsistent filament diameters... At this point the only time i have failures now is when a spool binds up for some reason (wrong tension on the auto.

My basic settings in cura are:. Getting it to print perfectly might take some work, but it works. Others have experienced nozzle clogging, likely as a result of inconsistent filament diameters.. 60, retraction 4,5 mm, retraction speed:

60, retraction 4,5 mm, retraction speed:.. 16.03.2021 · compared to other pla plus filament, the esun pla pro might be one of the more difficult ones to work with. How familiar are you with all of the printing settings in your slicer? I use esun pla plus and my nozzle temp is 216c and retraction speed is 40mm/s. Modified rostock max v2, prusa mk2, prusa mk3. It is direct drive so retraction amount is different. Setting unload speed at start to 120mm/s. Printer i am using is a sovol sv01 (direct drive) at (after a lot of fiddling) 205c/60c, 1.2mm/50mm/s retraction. I have to say that i was fairly satisfied with the print quality i was getting then. But every machine is different.

My basic settings in cura are:.. My basic settings in cura are: 60, retraction 4,5 mm, retraction speed: I get perfect results with all the colors, besides the white that i have some stringing and some blobs and zits, maybe a bad spool. Been up and down all the relevant cura settings with virtually no effect. Users have reported excessive stringing when printing with this filament. Make sure you do it with the fan … I print their pla+ at 205c, 60c bed. I use a test model (attached) with 10mm tall cone type towers of.

Printer i am using is a sovol sv01 (direct drive) at (after a lot of fiddling) 205c/60c, 1.2mm/50mm/s retraction.. Modified rostock max v2, prusa mk2, prusa mk3. Users have reported excessive stringing when printing with this filament. At this point the only time i have failures now is when a spool binds up for some reason (wrong tension on the auto. Been up and down all the relevant cura settings with virtually no effect. But every machine is different. I use esun pla+ and is working really good for me. Managed to get it to extrude okay, but temp was way up to 230°c and even at that temp there's still some underextrusion. Brand:esun pla + printing parameters: 23.10.2019 · stringing is gone, but underextrudes badly with default pla profile at 210°c.. If you need any support please leave your feedback.

Modified rostock max v2, prusa mk2, prusa mk3.. The esun pla+ printed better aside from the stringing. Getting it to print perfectly might take some work, but it works. I use esun pla plus and my nozzle temp is 216c and retraction speed is 40mm/s. Esun pla+ is a bit prone to stringing, so you want to make sure your retraction is set right (and stringing def increases at higher temps). New comments cannot be posted and votes cannot be cast.

My basic settings in cura are: Hotend temp 210, bed temp: Users have reported excessive stringing when printing with this filament. But every machine is different.

Others have experienced nozzle clogging, likely as a result of inconsistent filament diameters... .. My basic settings in cura are:

See pics, the failed print was at 210 and the other at 230 and slowed down the speed. Managed to get it to extrude okay, but temp was way up to 230°c and even at that temp there's still some underextrusion. How familiar are you with all of the printing settings in your slicer? Others have experienced nozzle clogging, likely as a result of inconsistent filament diameters. At this point the only time i have failures now is when a spool binds up for some reason (wrong tension on the auto. New comments cannot be posted and votes cannot be cast. If you need any support please leave your feedback. Stringing is usually caused by a classic case of not enough retraction. But every machine is different.. 17.08.2019 · posted november 25, 2020 · esun pla+ stringing/underextrusion just joined this forum.

New comments cannot be posted and votes cannot be cast. I do suggest that you do a pid tune if you haven't run one. But every machine is different. I have to say that i was fairly satisfied with the print quality i was getting then.